Southwest Research Institute (SwRI) Fire
Technology Department conducts standard tests (below) in accordance with
strict standard fire test methods used in industries:
| STANDARD TEST |
DESCRIPTION |
CONTACT |
| 10 CFR 50 |
Fire Tests of Penetration Seals, Protective Envelope and Flexible Barriers |
Barry Badders |
| 10 CFR 71 |
Package and Transportation of Radioactive Material |
Barry Badders |
| 16 CFR, Part 1633 |
Standard for the Flammability (Open Flame) of Mattress Sets |
David Ewan |
| 16 CFR, Section 1500.45 |
Determining Extremely Flammable Contents of Self-Pressurized Containers (Similar to ASTM D 3065) |
Tony Sauceda |
| 33 CFR/Part 154 Appendix A |
Guidelines for Detonation Flame Arresters |
Alexandra Joyce |
| 33 CFR/Part 154 Appendix B |
Standard Specification for Tank Vent Flame Arresters |
Alexandra Joyce |
| ABD 0031 |
Fire-Smoke-Toxicity (FST) Test Specification (Airbus Industries) |
Amber Faw |
| AC11 Sect. 5.3.5 and Sect. 5.4.5 |
Comparative Bond Test |
Barry Badders
Arturo Alvarez |
| AC11 Sect. 5.4 |
Freeze/Thaw Test |
Barry Badders |
| AC24 |
Sections 6.7, 6.9, 6.10, 6.11 Exterior Insulation and Finish System |
Barry Badders
Arturo Alvarez |
| AC59 |
Direct-applies Exterior Finish System |
Barry Badders
Arturo Alvarez
David Hintz
Marshall Sharp |
| AITM 2.0007 |
Determination of the Specific Optical Smoke Density of Aircraft Interior materials |
Amber Faw |
| AITM 3.0005 |
Determination of Specific Gas Components of Smoke Generated by Aircraft Interior Materials |
Amber Faw |
| ANI/MAERP |
Fire Tests of Protective Envelope Systems |
Barry Badders |
| ASTM (Various) |
Flash Point, Open and Closed Cup (and Fire Point) |
Christina Gomez |
| ASTM C 1166 |
Flame Propagation of Dense and Cellular Elastomeric Gaskets and Accessories |
Christina Gomez |
| ASTM D 1692 |
Flammability of Plastic Sheeting and Cellular Plastics |
Christina Gomez |
| ASTM D 1929 |
Ignition Properties of Plastics |
Christina Gomez |
| ASTM D 2015 |
Gross Calorific value of Coal and Coke by the Adiabatic Bomb Calorimeter |
Christina Gomez |
| ASTM D 2540 |
Drop-Weight Sensitivity of Liquid Monopropellants |
Alexandra Joyce |
| ASTM D 2584 |
Ignition Loss of Cured Reinforced Resins |
Barry Badders |
| ASTM D 2859 |
Flammability of Finished Textile Floor Covering Materials |
Christina Gomez |
| ASTM D 2863 |
Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
Christina Gomez |
| ASTM D 3014 |
Flame Height, Time of Burning, Mass Loss of Rigid Thermoset Cellular Plastics in a Vertical Position |
Christina Gomez |
| ASTM D 3065 |
Determining Extremely Flammable and Flammable Contents of Self-Pressurized Containers (Similar to 16 CFR, Section 1500.45) |
Tony Sauceda |
| ASTM D 3675 |
ASTM Test for Surface Flammability of Materials Using a Radiant Energy Source |
Amber Faw |
| ASTM D 5485 |
Standard Test Method for Determining the Corrosive Effect of Combustion Products Using the Cone Corrosimeter |
Christina Gomez |
| ASTM D 568 |
Flammability of Flexible Plastics |
Christina Gomez |
| ASTM D 635 |
Rate of Burning and/or Extent and Time of Burning of Self-Supporting Plastics in a Horizontal Position |
Christina Gomez |
| ASTM E 108 |
Fire Tests of Roof Coverings |
Marshall Sharp |
| ASTM E 119 |
Fire Tests of Building Construction and Materials |
Barry Badders |
| ASTM E 1226 |
Pressure and Rate of Pressure Rise for Combustible Dust |
Alexandra Joyce |
| ASTM E 1232 |
Temperature Limit of Flammability of Chemicals |
Alexandra Joyce |
| ASTM E 1273 |
Standard Specification for Tank Vent Flame Arresters |
Alexandra Joyce |
| ASTM E 1317 |
Flammability of Marine Surface Finishes |
Amber Faw |
| ASTM E 1321 |
Determining Material Ignition and Flame Spread Properties |
Amber Faw |
| ASTM E 1352 |
Cigarette Ignition Resistance of Mock-Up Upholstered Furniture Assemblies |
Christina Gomez |
| ASTM E 1353 |
Cigarette Ignition Resistance of Components of Upholstered Furniture |
Christina Gomez |
| ASTM E 1354 |
Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter (Cone Calorimeter) |
Christina Gomez |
| ASTM E 136 |
Behavior of Materials in a Vertical Tube Furnace at 750°C (1382°F) |
Christina Gomez |
| ASTM E 1491 |
Standard Test Method for Minimum Autoignition Temperature of Dust Clouds |
Alexandra Joyce |
| ASTM E 1515 |
Minimum Explosible Concentration of Combustible Dusts |
Alexandra Joyce |
| ASTM E 1529 |
Determining Effects of Large Hydrocarbon Pool Fires on Structural Members and Assemblies |
Barry Badders
Bill Bendele |
| ASTM E 1537 |
Fire Testing of Upholstered Furniture |
Tony Sauceda
David Ewan |
| ASTM E 1590 |
Fire Testing of Mattresses |
David Ewan |
| ASTM E 162 |
Surface Flammability of Materials Using a Radiant Heat Energy Source |
Amber Faw |
| ASTM E 1725 |
Fire Tests of Fire-Resistive Barrier Systems for Electrical System Components |
Barry Badders
Bill Bendele |
| ASTM E 1740 |
Determining the Heat Release Rate and Other Fire-Test-Response Characteristics of Wallcovering Composites Using a Cone Calorimeter |
Christina Gomez |
| ASTM E 1822 |
Fire Testing of Stacked Chairs |
Tony Sauceda
David Ewan |
| ASTM E 1966 |
Fire-Resistive Joint Systems |
Barry Badders
Arturo Alvarez
David Hintz
Barry Badders |
| ASTM E 1995 |
Measurement of Smoke Obscuration Using a Conical Radiant Source in a Single Closed Chamber, With the Test Specimen Oriented Horizontally |
Amber Faw |
| ASTM E 2010 |
Positive Pressure Fire Tests of Window Assemblies |
Barry Badders |
| ASTM E 2019 |
Standard Test Method for Minimum Ignition Energy of a Dust Cloud in Air |
Alexandra Joyce |
| ASTM E 2021 |
Standard Test Method for Hot-Surface Ignition Temperature of Dust Layers |
Alexandra Joyce |
| ASTM E 2074 |
Fire Tests of Door Assemblies |
Arturo Alvarez
David Hintz
Barry Badders |
| ASTM E 2079 |
Limiting Oxygen (Oxidant) Concentration in Gases and Vapors |
Alexandra Joyce |
| ASTM E 476 |
Thermal Instability of Confined Condensed Phase Systems (Confinement Test) |
Alexandra Joyce |
| ASTM E 487 |
Constant-Temperature Stability of Chemical Materials |
Alexandra Joyce |
| ASTM E 582 |
Minimum Ignition Energy and Quenching Distance in Gaseous Mixtures |
Alexandra Joyce |
| ASTM E 648 |
Critical Radiant Flux of Floor Covering Systems Using a Radiant Heat Energy Source [NIST (NBS) Flooring Radiant Panel] |
Amber Faw |
| ASTM E 659 |
Standard Test Method for Autoignition Temperature of Liquid Chemicals |
Alexandra Joyce |
| ASTM E 662 |
Specific Optical Density of Smoke Generated by Solid Materials (Smoke Chamber) |
Amber Faw |
| ASTM E 680 |
Drop Weight Impact Sensitivity of Solid-Phase Hazardous Materials |
Alexandra Joyce |
| ASTM E 681 |
Concentration Limits of Flammability of Chemicals |
Alexandra Joyce |
| ASTM E 695-97 |
Method for Measuring Relative Resistance of Wall, Floor, and Roof Constructions to Impact Loading |
Alexandra Joyce |
| ASTM E 771 |
Spontaneous Heating Tendency of Materials |
Alexandra Joyce |
| ASTM E 789 |
Standard Test Method for Dust Explosions in a 1.2-Litre Closed Cylindrical Vessel |
Alexandra Joyce |
| ASTM E 800 |
Gas Sampling Protocol |
Amber Faw |
| ASTM E 814 |
Fire Tests of Through Penetrations (Seals) |
Barry Badders
Arturo Alvarez
David Hintz |
| ASTM E 84 |
Surface Burning Characteristics of Building Materials |
Tony Sauceda |
| ASTM E 918 |
Standard Practice for Determining Limits of Flammability at Elevated Temperature and Pressure |
Alexandra Joyce |
| ASTM E 970 |
Critical Radiant Flux of Exposed Attic Floor Insulation Using a Radiant Heat Energy Source (Utilizes E 648 test apparatus-modified) |
Amber Faw |
| ASTM F 1173 |
Fire and Hydrostatic Tests of Composite Pipe. Similar to IMO A.753(18) |
Jason Huczek |
| ASTM F 1273 |
Standard Specifications for Tank Vent Flame Arrestors |
Alexandra Joyce |
| ASTM F 1387 |
Specification for Performance of Piping and Tubing Mechanically Attached Fittings |
Barry Badders
Bill Bendele |
| ASTM G 125 |
Measuring Liquid and Solid Material Fire Limits in Gaseous Oxidants |
Alexandra Joyce
Jason Huczek |
| ASTM G 72 |
Autogenous Ignition Temperature of Liquids and Solids in a High-Pressure Oxygen-Enriched Environment |
Alexandra Joyce |
| ASTM G 74 |
Ignition Sensitivity of Materials to Gaseous Fluid Impact |
Alexandra Joyce |
| Bellcore GR-63-CORE (NEBS) |
Network Equipment Building Services |
Bill Bendele |
| BOEING BSS 7238 |
Smoke Test (Boeing) |
Amber Faw |
| BOEING BSS 7239 |
Toxicity Test (Boeing) |
Amber Faw |
| BOEING BSS 7304 |
Determination of Surface Flammability of Materials Using a Radiant Energy Source |
Amber Faw |
| BS 476 Part 20, 24 |
Equivalent or similar to ASTM E 119 |
Barry Badders
Arturo Alvarez
David Hintz
Marshall Sharp |
| BS 7244 |
British Standard Specification for Flame Arresters for General Use |
Alexandra Joyce |
| CA Technical Bulletin 106 |
Smoldering Cigarette Test for Mattress |
David Ewan |
| CA Technical Bulletin 116 |
Cigarette Test of Upholstered Furniture |
Christina Gomez |
| CA Technical Bulletin 117 |
Flame Retardance of Resilient Filling Materials Used in Upholstered Furniture |
Christina Gomez |
| CA Technical Bulletin 121 |
Flame Retardance of Resilient Filling Materials Used in Upholstered Furniture |
Christina Gomez |
| CA Technical Bulletin 129 |
Flammability Test for Mattresses for use in Public Buildings |
Tony Sauceda |
| CA Technical Bulletin 133 |
Flammability Test Procedure for Seating Furniture for Use in Public Occupancies |
Tony Sauceda |
| CA Technical Bulletin 603 |
Open-Flame Standard for Mattresses |
Tony Sauceda |
| CA Technical Bulletin 604 |
Bed Clothing Open-Flame Standard |
Tony Sauceda |
| CAL – 19 |
California, State of, Title 19, Chapter 8, Articles 1-11 |
Tony Sauceda |
| California Building Code Chapter 7A; 12-7A-5 |
Urban Wildland Interface Building Test Standards- Fire Resistance Standards for Decks and Other Horizontal Structures |
Barry Badders
Marshall Sharp |
| CGA C14 |
Procedures for Fire Testing of DOT Cylinders Pressure Relief Device Systems |
Alexandra Joyce |
| CSA-Z343, Rev 12 |
Test Method for In-Line and Firebox Flame Arresters |
Alexandra Joyce |
| DOC-FF-1-170 |
Equivalent or similar to ASTM D 2859 |
Christina Gomez |
| DoD (Various) |
Safety and Performance Tests for Qualification of Explosives and Explosives Hazards Classification |
Alexandra Joyce |
| DOT 49 CFR 393.67 |
Liquid Fuel Tanks |
Bill Bendele |
| Drager Tubes |
Colorimetric Toxicity |
Amber Faw |
| ECE R34 |
Annex 5, “Testing of Fuel Tanks Made of Plastic Material” |
Bill Bendele |
| EN 12874 |
Flame Arresters-Specifications, Operational Requirements and Test Procedures |
Alexandra Joyce |
| EN 13501-1 |
Fire Classification of Construction Products Using Reaction to Fire Tests |
Amber Faw |
| EN ISO 11925-2 |
Ignitability of building products subjected to direct impingement of flame -- Part 2: Single-flame source test |
Christina Gomez |
| EPA T0-15 |
Determination of Volatile Organic Compounds (VOCs) by GC-MS |
Amber Faw |
| FAR Part 23.853 |
Vertical Bunsen Burner Test for Passenger and Crew Compartment Interiors |
Christina Gomez |
| Fire Block Test of Seats |
National Standards for School Buses and School Bus Operations |
Tony Sauceda |
| FM 4880 |
Flammability Apparatus, Room Corner Test, 25 ft and 50 ft Corner Test |
Jason Huczek |
| FM 4910 |
Clean Room Tests |
Barry Badders
Bill Bendele |
| FM 4922 |
Flame/Smoke Exhaust Ducts |
Bill Bendele |
| FM 4995 |
Commodity Classification of Idle Plastic Pallets |
Jason Huczek |
| FM 6061 |
FMRC Test Procedure for Flame Arresters for Storage Tank Vent Pipes, Class 6061 |
Alexandra Joyce |
| FM 6930 |
Flammability Classification of Industrial Fluids |
Jason Huczek |
| FM 7371 |
FMRC Test Procedure for Detonation Arresters, Class 737 |
Alexandra Joyce |
| FMCSA 49CFR 393.67 (Federal Motor Carrier Safety Administration) |
Safety Venting TestPressure ResistanceLeakage TestDrop TestFill Pipe Test |
Bill Bendele |
| FMVSS 304 |
Compressed Natural Gas (CNG) Fuel Container Integrity |
Bill Bendele |
| FTIR |
Toxic Gas Analysis |
Amber Faw |
| FTS 191 |
Various Test Methods:5903: Vertical 12- or 60-second Flame Test for Fabrics5906: Horizontal 12- or 60-second Flame Test for Fabrics5908: 45º Angle 12- or 60-second Flame Test for Fabrics |
Christina Gomez |
| FTS 372 |
Equivalent or similar to ASTM E 648 |
Amber Faw |
| IEEE 383 |
Wire/Cable Vertical Flame Test |
Tony Sauceda |
| IEEE 634 |
Equivalent or similar to ASTM E 814 |
Barry Badders
Arturo Alvarea
David Hintz |
| IMO A.653(18) |
Surface Flammability of Bulkhead, Ceiling, and Such Finish Materials |
Amber Faw |
| IMO A.753 (18) |
Guidelines for the Application of Plastic Pipes on Ships. Similar to ASTM F 1173 |
Jason Huczek |
| IMO A.754(18) |
Recommendation of Fire Resistance Tests for "A," "B," and "F" Class Divisions |
Barry Badders |
| IMO FTP Code Part 1 |
Non-Combustibility Test |
Christina Gomez |
| IMO FTP Code Part 2 |
Smoke and Toxicity Test |
Amber Faw |
| IMO FTP Code Part 5 |
Test for Surface Flammability |
Amber Faw |
| IMO FTP Code Part 6 |
Test for Primary Deck |
Amber Faw |
| IMO FTP Code Part 7 |
Test for Vertically Supported Textiles and Films |
Christina Gomez |
| IMO FTP Code Part 8 |
Test for Upholstered Furniture |
Christina Gomez |
| IMO FTP Code Part 9 |
Test for Bedding Components |
Christina Gomez |
| ISO 1182 |
Non-Combustibility of Materials |
Christina Gomez |
| ISO 15029 |
Determination of spray ignition characteristics of fire-resistant fluids |
Jason Huczek |
| ISO 15540 |
Ships and Marine Technology - Fire Resistance of Hose Assemblies |
Barry Badders
Bill Bendele |
| ISO 15541 |
Ships and Marine Technology - Fire Resistance of Hose Assemblies |
Barry Badders
Bill Bendele |
| ISO 1716 |
Heat of Combustion – Determination of the Calorific Value |
Christina Gomez |
| ISO 20823 |
Determination of the flammability characteristics of fluids in contact with hot surfaces -- Manifold ignition test |
Alexandra Joyce |
| ISO 3008 |
Equivalent or similar to ASTM E 152 |
Barry Badders
Arturo Alvarez
David Hintz |
| ISO 3009 |
Equivalent or similar to ASTM E 163 |
Barry Badders |
| ISO 5659 Part 2 |
Optical Density Test |
Amber Faw |
| ISO 5660 |
Rate of Heat Release from Building Products (Cone Calorimeter Method) |
Christina Gomez |
| ISO 834 |
Fire Resistance Test |
Barry Badders |
| ISO 9239-1 |
Determination of Burning Behavior Using a Radiant Heat Source |
Amber Faw |
| ISO 9705 |
Room/Corner Test |
Tony Sauceda
David Ewan |
| MIL-STD-810, Method 511 |
Explosive Atmosphere |
Alexandra Joyce |
| MIL-T-24708(SH) |
Quarter-Scale Tests |
Tony Sauceda |
| NES 711 |
Determination of Smoke Index of the Products of Combustion from Small Specimens of Materials |
Amber Faw |
| NES-713 |
Bunsen Burner Flame Test with Draeger Tube Toxicity Determinations |
Amber Faw |
| NFPA 251 |
Equivalent or similar to ASTM E 119 |
Barry Badders
Arturo Alvarez
David Hintz
Marshall Sharp |
| NFPA 252 |
Equivalent or similar to ASTM E 152 |
Barry Badders
Arturo Alvarez
David Hintz |
| NFPA 253 |
Equivalent or similar to ASTM E 648 |
Amber Faw |
| NFPA 255 |
Equivalent or similar to ASTM E 84 |
Tony Sauceda |
| NFPA 256 |
Equivalent or similar to ASTM E 108 |
Marshall Sharp |
| NFPA 258 |
Equivalent or similar to ASTM E 662 |
Amber Faw |
| NFPA 259 |
Potential Heat of Building Materials |
Christina Gomez |
| NFPA 260 |
Cigarette Ignition Resistance of Components of Upholstered Furniture |
Christina Gomez |
| NFPA 261 |
Resistance of Mock-Up Upholstered Furniture Material Assemblies to Ignition by Smoldering Cigarettes |
Christina Gomez |
| NFPA 265 |
Equivalent or similar to UBC 8-2 |
Tony Sauceda
David Ewan |
| NFPA 266 |
Test of Upholstered Furniture Exposed to Flaming Ignition Source |
Tony Sauceda |
| NFPA 267 |
Test of Mattresses and Bedding Assemblies Exposed to Flaming Ignition Source |
Tony Sauceda |
| NFPA 268 |
Radiant Panel Test Exterior Wall Systems |
Barry Badders
Marshall Sharp |
| NFPA 271 |
Equivalent or similar to ASTM E 1354 |
Christina Gomez |
| NFPA 285 |
Method of Test for the Evaluation of Flammability Characteristics of Exterior, Nonload-bearing Wall Assemblies Containing Combustible Components Using the Intermediate-Scale, Multistory Test Apparatus (ISMA) |
Barry Badders
Arturo Alvarez
David Hintz |
| NFPA 286 |
Standard Methods of Fire Tests for Evaluating Contribution of Wall and Ceiling Interior Finish to Room Fire Growth |
Tony Sauceda |
| NFPA 30/30A |
Flammable and Combustible Liquids Code |
Barry Badders |
| NFPA 415 |
Airport Terminal Buildings, Fueling Ramp Drainage, and Loading Walkways |
Barry Badders
Arturo Alvarez
David Hintz |
| NFPA 417 |
Fire Tests of Aircraft Loading Walkways |
Barry Badders
Arturo Alvarez
David Hintz |
| NFPA 58 |
Storage and Handling of Liquefied Petroleum Gases. Equivalent or similar to 49 CFR Section 179.105-4 and 179-105-7 |
Barry Badders
Bill Bendele |
NFPA 701/UL214
Test 1/Test 2 |
Fire Tests for Flame-Resistant Textiles and Films: Large Scale and Small Scale |
Christina Gomez |
| OTI 95/634 |
Jet Fire Test |
Barry Badders
Arturo Alvarez |
| SAE J1527 |
Marine Fuel Hose Fire Resistance Tests |
Bill Bendele |
| SAE J1942 |
Hose and Hose Assemblies for Marine Applications |
Bill Bendele |
| SBI - EN 13823 |
European Single Burning Item Test |
David Ewan |
| School Bus Seat |
School Bus Seat Upholstered Fire Block Test |
Tony Sauceda |
| SMP 800-C |
Bombardier Toxicity Test |
Amber Faw |
| STD791C, Method 6052.1 |
High Temperature-High Pressure Spray Ignition Test |
Barry Badders
Bill Bendele |
| STD791C, Method 6053.1 |
Manifold Ignition Test |
Tony Sauceda |
| SwRI 00-01 |
Fire Performance Evaluation of Fondue Pot Burners |
Barry Badders
Bill Bendele |
| SwRI 91-01 |
Small Scale Fire Test for Paper, Corrugated Board, and Thin Materials |
Barry Badders
Bill Bendele |
| SwRI 93-01 |
Fire, Hose Steam, Impact, Ballistic and Leakage Tests |
Barry Badders
Bill Bendele |
| SwRI 95-03 |
Testing Requirements for Multi-Hazard Aboveground Flammable Liquid/Fuel Storage Tanks |
Barry Badders
Bill Bendele |
| SwRI 97-02 |
Hydraulic Test of Automobile Fuel Tank |
Bill Bendele |
| SwRI 99-01 |
Testing Requirements for Liquid Hydrocarbon Pool-Fire Testing of Aboveground Flammable Liquid/Fuel Storage Tanks (AST) and Liquid Petroleum Gas (LPG) Storage Tanks Containing Fuel |
Barry Badders
Bill Bendele |
| UBC 17-3 |
See New Common Code UBC 26-2 |
Barry Badders
Arturo Alvarez
David Hintz
Marshall Sharp |
| UBC 17-5 |
See New Common Code UBC 26-3 |
Tony Sauceda |
| UBC 17-6 |
See New Common Code UBC 26-4 |
Barry Badders
Arturo Alvarez
David Hintz
Marshall Sharp |
| UBC 26-2 |
Evaluation of Thermal Barriers (Formerly UBC 17-3) |
Barry Badders
Arturo Alvarez
David Hintz
Marshall Sharp |
| UBC 26-3 |
Room Fire Test for Interior of Foam Plastic Systems (formerly UBC 17-5) |
Tony Sauceda |
| UBC 26-6 |
Ignition Properties of Plastics |
Christina Gomez |
| UBC 26-7 |
Method of Test for Determining Classification of Approved Light-Transmitting Plastics |
Tony Sauceda |
| UBC 26-8 |
Room Fire Test Standard for Garage Doors Using Foam Plastic Insulation |
Tony Sauceda |
| UBC 26-9 |
Method of Test for the Evaluation of Flammability Characteristics of Exterior, Nonload-bearing Wall Assemblies Containing Combustible Components Using the Intermediate-Scale, Multistory Test Apparatus (ISMA) |
Barry Badders
Arturo Alvarez
David Hintz
Marshall Sharp |
| UBC 42-1 |
See New Common Code UBC 8-1 |
Tony Sauceda |
| UBC 42-2 |
See New Common Code UBC 8-2 |
Barry Badders
Tony Sauceda |
| UBC 43-6 |
See New Common Code UBC 7-5 |
Barry Badders |
| UBC 7-2 |
Fire Tests of Door Assemblies |
Barry Badders
Arturo Alvarez
David Hintz |
| UBC 7-5 |
Fire Tests of Through-Penetration Fire Stops (formerly UBC 43-6) |
Barry Badders
Arturo Alvarez
David Hintz |
| UBC 8-1 |
Surface Burning Characteristics of Building Materials. Equivalent or similar to ASTM E 84 (Formerly UBC 42-1) |
Tony Sauceda |
| UBC 8-2 |
Evaluating Room Fire Growth Contribution of Textile Wallcovering (Formerly UBC 42-2) |
Tony Sauceda
Barry Badders |
| UFC 79-7 |
Aboveground Storage Tanks |
Barry Badders
Bill Bendele |
| UL 10A and 10B |
Equivalent or similar to ASTM E 152 |
Barry Badders
Arturo Alvarez
David Hintz |
| UL 1479 |
Equivalent or similar to ASTM E 814 |
Barry Badders
Arturo Alvarez
David Hintz |
| UL 155 |
Equivalent or similar to ASTM E 152 |
Barry Badders
Bill Bendele |
| UL 162 |
Standard for Foam Equipment and Liquid Concentrates |
Jason Huczek |
| UL 1684 |
Reinforced Thermosetting Resin Conduit (RTRC) and Fittings |
Tony Sauceda |
| UL 1709 |
Standard for Rapid Rise Fire Tests if Protection Materials for Structural Steel Equivalent or similar to UK-DOE Fire Curve, Mobil Fire Curve, and NPD Fire Curve |
Barry Badders |
| UL 1715 |
Fire Test of Interior Finish Material |
Tony Sauceda |
| UL 1975 |
Fire Test of Foamed Plastics Used for Decorative Purposes |
Tony Sauceda |
| UL 199 |
Automatic Sprinklers for Fire-Protection Service |
Jason Huczek |
| UL 2024 |
Standard for Test Method for Flame and Smoke Characteristics of Nonmetallic Raceway Used in Environmental Air-Handling Spaces |
Tony Sauceda |
| UL 2043 |
Fire Test for Heat and Visible Smoke Release for Discrete Product and their Accessories Installed in Air-Handling Spaces |
David Ewan |
| UL 2080 |
Fire Resistant Tanks for Flammable and Combustible Liquids |
Barry Badders
Bill Bendele |
| UL 2085 |
Fire, Hose Stream, Impact, Ballistic and Leakage Tests. Equivalent or similar to UFC Appendix II-F, 79-7 |
Barry Badders
Bill Bendele |
| UL 2218 |
Impact Resistance Test of Prepared Roofing |
Barry Badders
Marshall Sharp |
| UL 2335 |
Fire Tests of Storage Pallets |
Jason Huczek |
| UL 525 |
Flame Arresters for Use on Vents of Storage Tanks for Petroleum Oil and Gasoline |
Alexandra Joyce |
| UL 555 |
Fire Dampers and Ceiling Dampers |
Barry Badders
Arturo Alvarez
David Hintz |
| UL 711 |
Standard for Rating and Fire Testing of Fire Extinguishers |
Jason Huczek |
| UL 72 |
Tests for Fire Resistance of Record Protection Equipment |
Barry Badders
Bill Bendele |
| UL 723 |
Equivalent or similar to ASTM E84 |
Tony Sauceda |
| UL 790 |
Equivalent or similar to ASTM E108 |
Barry Badders
Marshall Sharp |
| UL 9 |
Equivalent or similar to ASTM E 163 |
Barry Badders
Arturo Alvarez
David Hintz |
| UL 94 |
Standard Tests for Flammability of Plastic Materials for Parts in Devices and Appliances |
Christina Gomez |
| UL C102.2 (Canada) |
Canadian Safety Standard 102.2. Equivalent or similar to ASTM E 84 |
Tony Sauceda |
| UN Practices & Procedures |
Various HazMat Classification Procedures, Test Methods and Criteria, Transport of Dangerous Goods |
Alexandra Joyce |
| United Nations Practices and Procedures |
Self-Accelerating Decomposition Temperature (SADT) |
Alexandra Joyce |
| UPITT Smoke Toxicity |
Evaluation of the Acute Inhalation Toxicity of the Combustion Products of Materials Using the University of Pittsburgh Test Method |
Amber Faw |
| USBM RI 5624 |
Explosibility of Dusts (Laboratory Equipment and Test Procedures for Evaluating) |
Alexandra Joyce |
For more information about fire technology services and
capabilities for third-party listing and labeling and
third-party production control programs and product
certification at SwRI or how you can contract with SwRI,
please call (210) 522-2311 or e-mail
fire-info@swri.org.
